TROUBLESHOOTING GUIDE - Zamboni® Ice Resurfacer
| MALFUNCTION | PROBABLE CAUSE | CORRECTIVE ACTION |
| Unsatisfactory shaving Blade leaving wavy ice conditions | Dull blade | *BLADE MUST BE SHARP. Most often the cause of shaving problems. A sharp blade will shave easier and will not tend to push the conditioner off the ice. |
| Blade chatters | Blade at incorrect angle Tire pressure low Lift bar and down pressure mechanism Bushings worn Cylinder working improperly Springs in conditioner | *Refer to Operating Instructions. The angle of the blade should be about 10º in relation to the conditioner runner. Can affect shaving. Inflate tires to correct and uniform pressure. *See Parts Manual for illustration of cylinder and related components. Check for leaks. It may be necessary to repack the cylinder or replace it. Check pins at both ends of cylinder for excessive wear and slop. *Leaf springs and coil springs must be in good condition ard tight if the blade holding bar is to be held firm. |
| Grooving the ice | Dull blade | *When the blade is dull, operator often lowers blade to cut more. The blade may then be far below the runners and may actually lift the conditioner off the runners when traveling straight ahead. If making a turn with blade set this way, grooving of ice will likely occur. Install a sharp blade and recheck. |
| Conditioner leaving scratch on ice | Nick in blade Foreign matter on runners or other parts of conditioner | *Sharpen *Check and remove foreign matter. File. |
| Difficult to adjust blade | Worn parts Dirt, debris in mechanism | *Check blade adjusting screw and re- lated parts. *Clean completely. |
| Conditioner runners riding high off ice | Dull blade Runners not straight Twist in conditioner | *When clull, blade tends to lift the runners off the ice. Try a freshly sharpened knife. *Check with straight edge. *Set on level surface. Disconnect from lift bar. |
| Leakage from side of conditioner | Dull blade lifting conditioner Improper fit at ends of squeegee | *Change blade; -- test. *Adjust or replace squeegee. Ends of squeegee should be tight to con- ditioner side plates. |
| Water freezing unevenly an surface | Cool water used on extremely cold ice surface | *Use hot water as ice making water. |
| Ice thickness building up too fast | Dull blade Blade at wrong angle Too much water | *Install sharp blade. *Set blade at approximately 10º as explained in Operating Instructions, *Keep closer control on water. After light skating session, |
| Ice building up on edges | Not edging often enough | Use edger more frequently |
| Unable to make good sheet of in single pass | Not using wash water when resurfacing | *Use wash water operation in conjunction with other resurfacing operations |
| Ice buildup in front of blade | Dull blade Blade angle too flat | *A sharp blade will create more agitation of the shaven snow at the blade edge than a dull blade. Sharpen blade so snow is forced into conveyor *Check to see that blade is at least set at 10º. |
| Machine skidding, inadequate traction | Tire pressure low Oil getting on tires Dull blade Tires worn | Inflate tires to correct and uniform pressure. Check and eliminate oil leaks on machine. Clean floor of storage room to eliminate oil. *Put on sharp blade. Adjust Kick the can crew official site. 2021年4月04日(日) 「hy sky fes 2020→2021」に出演決定！. Explore releases from Kick The Can Crew at Discogs. Shop for Vinyl, CDs and more from Kick The Can Crew at the Discogs Marketplace. Kick the can crew 住所 rar. TUNGSTEN TIP. See that studs are in good condition. |
| Difficult to steer | Insufficient lubrication Tire pressure low Worn or loose steering linkage | Lubricate steering linkage. Inflate tires to correct and uniform pressure. Refer to Parts List. Check steering system completely including |
| Inadequate hydraulic pressure | Lack of oil Oil filter dirty Faulty hydraulic pump Sticky relief valve | Check and add as required. Change oil filter. Parts probably worn. Replace or rebuild pump. Replace relief valve. |
| Inadequate power of conveyor | Engine RPM too low Faulty seat on conveyor motor Faulty pump | Check by selecting lower hydrostatic transmission selector setting and higher engine RPM. Disconnect small drain hose from motor and check amount of oil coming out of seal drain Check by moving valve handles so that cylinder 'bottoms out'. You should hear oil going 'over relief' and engine RPM drop slightly. If faulty rebuild or replace motor. |
| Hydraulic cylinder leaks | Worn or cracked packing | Overhaul cylinder and replace cylinder packing. |
| Conditioner won't lift high enough | Tire pressure low | Inflate to correct pressure. |
| Water pump will not work | Water lines plugged Broken or loose belt Burned out impeller | *Flush water lines. *Check. Replace if needed. *Replace impeller. Clean pump completely before replacing. Try pump while impeller is removed. |
| Water coming around the front of the conditioner | Water pump not working Terraria mod browser offline. Too much wash water | *See item above. *If more wash water is being dropped than the pump is picking up, squeegee will push it forward of the blade. Correct by cutting down slightly on amount of wash water being used. |
| Slush being left machine | Improper fit on squeegee Wash water system not working properly | *Check. Replace if needed. *Check complete system. Inlet may be plugged thereby causing water and snow to be forced under squeegee. |
| Water valve difficult to operate | Damaged valves | *If valve is frozen while in closed position pressure of ice may have deformed stem of valve. Check. Replace valve if necessary. |
| Will not spread water evenly | Water distributor pipe clogged | *Flush out water tanks well. Remove ends of distributor pipe and clean completely. |
Free download zamboni maintenance manuals PDF PDF Manuals Library ZAMBONI MAINTENANCE MANUALS PDF Digital library is a good source of information for everyone who zamboni 440 - free pdf ebook downloads zamboni 440 at greenbookee.net - Download free pdf files,ebooks and documents of zamboni 440 zamboni service manual documents. Zamboni 440 et 445 8R-04410 Zamboni 520, 525, 552 et 560 8R-16800 Roller board 8R-0500B OPTIONAL Bumper with lower guide wheel 8T-15900 HEADLIGHT Zamboni Incandescents Halogenes 400-440 7L-04011 445 7L-04022 520-552. 7L-17970 525-552-560 7L-17980. halogene headlight for serial number higher than 9362.
Zamboni operating manual download on twogentsproductions-3.com free books and manuals search - Zamboni Repair Manual zamboni 440 - free pdf ebook downloads zamboni 440 at greenbookee.net - Download free pdf files,ebooks and documents of zamboni 440.
TROUBLESHOOTING GUIDE - Zamboni® Ice Resurfacer
| MALFUNCTION | PROBABLE CAUSE | CORRECTIVE ACTION |
| Unsatisfactory shaving Blade leaving wavy ice conditions | Dull blade | *BLADE MUST BE SHARP. Most often the cause of shaving problems. A sharp blade will shave easier and will not tend to push the conditioner off the ice. |
| Blade chatters | Blade at incorrect angle Tire pressure low Lift bar and down pressure mechanism Bushings worn Cylinder working improperly Springs in conditioner | *Refer to Operating Instructions. The angle of the blade should be about 10º in relation to the conditioner runner. Can affect shaving. Inflate tires to correct and uniform pressure. *See Parts Manual for illustration of cylinder and related components. Check for leaks. It may be necessary to repack the cylinder or replace it. Check pins at both ends of cylinder for excessive wear and slop. *Leaf springs and coil springs must be in good condition ard tight if the blade holding bar is to be held firm. |
| Grooving the ice | Dull blade | *When the blade is dull, operator often lowers blade to cut more. The blade may then be far below the runners and may actually lift the conditioner off the runners when traveling straight ahead. If making a turn with blade set this way, grooving of ice will likely occur. Install a sharp blade and recheck. |
| Conditioner leaving scratch on ice | Nick in blade Foreign matter on runners or other parts of conditioner | *Sharpen *Check and remove foreign matter. File. |
| Difficult to adjust blade | Worn parts Dirt, debris in mechanism | *Check blade adjusting screw and re- lated parts. *Clean completely. |
| Conditioner runners riding high off ice | Dull blade Runners not straight Twist in conditioner | *When clull, blade tends to lift the runners off the ice. Try a freshly sharpened knife. *Check with straight edge. *Set on level surface. Disconnect from lift bar. |
| Leakage from side of conditioner | Dull blade lifting conditioner Improper fit at ends of squeegee | *Change blade; -- test. *Adjust or replace squeegee. Ends of squeegee should be tight to con- ditioner side plates. |
| Water freezing unevenly an surface | Cool water used on extremely cold ice surface | *Use hot water as ice making water. |
| Ice thickness building up too fast | Dull blade Blade at wrong angle Too much water | *Install sharp blade. *Set blade at approximately 10º as explained in Operating Instructions, *Keep closer control on water. After light skating session, |
| Ice building up on edges | Not edging often enough | Use edger more frequently |
| Unable to make good sheet of in single pass | Not using wash water when resurfacing | *Use wash water operation in conjunction with other resurfacing operations |
| Ice buildup in front of blade | Dull blade Blade angle too flat | *A sharp blade will create more agitation of the shaven snow at the blade edge than a dull blade. Sharpen blade so snow is forced into conveyor *Check to see that blade is at least set at 10º. |
| Machine skidding, inadequate traction | Tire pressure low Oil getting on tires Dull blade Tires worn | Inflate tires to correct and uniform pressure. Check and eliminate oil leaks on machine. Clean floor of storage room to eliminate oil. *Put on sharp blade. Adjust Kick the can crew official site. 2021年4月04日(日) 「hy sky fes 2020→2021」に出演決定！. Explore releases from Kick The Can Crew at Discogs. Shop for Vinyl, CDs and more from Kick The Can Crew at the Discogs Marketplace. Kick the can crew 住所 rar. TUNGSTEN TIP. See that studs are in good condition. |
| Difficult to steer | Insufficient lubrication Tire pressure low Worn or loose steering linkage | Lubricate steering linkage. Inflate tires to correct and uniform pressure. Refer to Parts List. Check steering system completely including |
| Inadequate hydraulic pressure | Lack of oil Oil filter dirty Faulty hydraulic pump Sticky relief valve | Check and add as required. Change oil filter. Parts probably worn. Replace or rebuild pump. Replace relief valve. |
| Inadequate power of conveyor | Engine RPM too low Faulty seat on conveyor motor Faulty pump | Check by selecting lower hydrostatic transmission selector setting and higher engine RPM. Disconnect small drain hose from motor and check amount of oil coming out of seal drain Check by moving valve handles so that cylinder 'bottoms out'. You should hear oil going 'over relief' and engine RPM drop slightly. If faulty rebuild or replace motor. |
| Hydraulic cylinder leaks | Worn or cracked packing | Overhaul cylinder and replace cylinder packing. |
| Conditioner won't lift high enough | Tire pressure low | Inflate to correct pressure. |
| Water pump will not work | Water lines plugged Broken or loose belt Burned out impeller | *Flush water lines. *Check. Replace if needed. *Replace impeller. Clean pump completely before replacing. Try pump while impeller is removed. |
| Water coming around the front of the conditioner | Water pump not working Terraria mod browser offline. Too much wash water | *See item above. *If more wash water is being dropped than the pump is picking up, squeegee will push it forward of the blade. Correct by cutting down slightly on amount of wash water being used. |
| Slush being left machine | Improper fit on squeegee Wash water system not working properly | *Check. Replace if needed. *Check complete system. Inlet may be plugged thereby causing water and snow to be forced under squeegee. |
| Water valve difficult to operate | Damaged valves | *If valve is frozen while in closed position pressure of ice may have deformed stem of valve. Check. Replace valve if necessary. |
| Will not spread water evenly | Water distributor pipe clogged | *Flush out water tanks well. Remove ends of distributor pipe and clean completely. |
Free download zamboni maintenance manuals PDF PDF Manuals Library ZAMBONI MAINTENANCE MANUALS PDF Digital library is a good source of information for everyone who zamboni 440 - free pdf ebook downloads zamboni 440 at greenbookee.net - Download free pdf files,ebooks and documents of zamboni 440 zamboni service manual documents. Zamboni 440 et 445 8R-04410 Zamboni 520, 525, 552 et 560 8R-16800 Roller board 8R-0500B OPTIONAL Bumper with lower guide wheel 8T-15900 HEADLIGHT Zamboni Incandescents Halogenes 400-440 7L-04011 445 7L-04022 520-552. 7L-17970 525-552-560 7L-17980. halogene headlight for serial number higher than 9362.
Zamboni operating manual download on twogentsproductions-3.com free books and manuals search - Zamboni Repair Manual zamboni 440 - free pdf ebook downloads zamboni 440 at greenbookee.net - Download free pdf files,ebooks and documents of zamboni 440.
Zamboni Operator Manual 440 Online
Zamboni 440 et 445 8R-04410 Zamboni 520, 525, 552 et 560 8R-16800 Roller board 8R-0500B OPTIONAL Bumper with lower guide wheel 8T-15900 HEADLIGHT Zamboni Incandescents Halogenes 400-440 7L-04011 445 7L-04022 520-552. 7L-17970 525-552-560 7L-17980. halogene headlight for serial number higher than 9362. Pre-owned Zamboni Ice Resurfacers, Propoane, Natural Gas, or Battery Powered Electric Models Available. All units have been recently serviced by the Zamboni Authorized Dealer & Service Provider. Models 520, 526, 440, 446, 552. Call or email for information.
